Rendered at 19:27:57 GMT+0000 (Coordinated Universal Time) with Cloudflare Workers.
kens 8 days ago [-]
Author here for your DTL questions...
abbeyj 2 days ago [-]
The caption below the pinout for the 616A calls it a quad NAND, but it is a dual NAND.
The text says that the 616A uses the two diodes that are unused in the 680A but your hypothesized metal layer for the 616A shows those diodes as being unused. They are shown as being used in the hypothesized metal layer for the 670A though. The 670A and the 680A both need 12 diodes and the 616A only needs 10, if I counted correctly. And yet there are 14 total diodes on the die so none of these three models needs all of them. Maybe it was easier to route the signals this way?
kens 2 days ago [-]
Thank you for the corrections; I've updated the post and credited you. While fixing this, I noticed that the databook was wrong, calling the 616A a dual 3-input chip, when the gates have 4 inputs.
MeteorMarc 2 days ago [-]
Why is DTL slower than TTL?
adrian_b 2 days ago [-]
The reason is not seen in the schematics from TFA, because these are some early DTL gates, which are even slower, but for other motives, i.e. because they use a pull-up resistor at output.
To improve their speed, one must use a totem-pole output, where at the output the pull-up resistor is replaced by a transistor, so that the output can charge quickly a capacitive load, ensuring fast transitions from low to high.
Then only 1 of the 2 output transistors is on, depending on the logic state.
So those 2 transistors must have inputs of opposite polarities. This is done by connecting the pull-up transistor to the collector of the driver transistor and the pull-down transistor to the emitter of the driver transistor.
In the gate with totem-pole output, there must be a level-shifting diode connected to the base of the driver transistor, to ensure that the threshold between "0" and "1" is the same at input and at output, i.e. the threshold is equal with 2 silicon diode voltage drops (the 2 diodes are the emitter junction of the driver transistor in series with the emitter junction of the pull-down output transistor), i.e. approximately 1.4 volt (which is the midpoint between the levels that are defined as the limits for "0" and "1", i.e. 0.8 volt and 2.0 volt, leaving a margin for noise that will not cause a wrong logic value).
When an input to the totem-pole DTL goes from high to low, the level-shifting diode becomes reverse biased, so current cannot pass through it, so the driver transistor remains with an open base. Bipolar transistors that are blocked by leaving their base open, become off only very slowly, because there is no path to evacuate the charge carriers from their base region, and until all mobile charge carriers from the base decay by recombination, the transistor remains on, which may take many microseconds.
In TTL, the difference from totem-pole DTL is that the input diodes and the level-shifting diode are no longer separated by an isolation diffusion and they are close enough so that the bipolar transistor effect appears between them.
Thus the input diodes become multiple emitter junctions of a bipolar transistor, while the level-shifting diode becomes the collector junction of that transistor.
The bipolar transistor effect consists in the fact that if there exists an emitter current, it passes through the collector junction, despite the fact that it is reverse biased, which in an isolated diode would prevent the passing of any current.
Thus the transistor effect ensures that when the input goes from high to low, there is a current through the level-shifting diode, which removes the mobile charge carriers from the base of the driver transistor, ensuring that it becomes off immediately, so the TTL gate switches faster than the DTL gate when the input goes from high to low (and the output goes from low to high, because the simplest TTL and DTL gates are inverting gates).
After TTL gates with a power supply of 5 volt replaced the DTL gates in computers, there was a DTL variant that survived until the mid seventies. That DTL variant used a higher supply voltage, typically of 15 volt, to ensure a high noise immunity in industrial applications, where the lower speed also did not matter much. That variant of DTL was eventually replaced by the CMOS 4000 series of logic circuits, initially introduced by RCA, which used the same power supply, but which had a much lower power consumption.
iberator 2 days ago [-]
Do you know schemes for any DTL cpus/mcus?
kens 2 days ago [-]
The popular IBM System/360 series used DTL gates, typically AND-OR-Invert. These were not exactly integrated circuits, but used square hybrid modules. These modules had separate transistor dies, diode dies, and thick-film resistors on a ceramic substrate. These modules were called SLT (Solid Logic Technology). IBM used these modules because they didn't think ICs were mature enough at the time.
But seriously, is it possible to analyze the modern chips like Apple M1 using the same methods? To find out, for instance, why there are so much more efficient than Intel CPUs?
simcop2387 2 days ago [-]
It'd almost certainly need some other kind of microscopy to start digging into them because the feature sizes are going to be on the orders of 10s of nanometers if not smaller. Combine that with the sheer massive size in terms of both physical die and how many transistors, it's almost certainly technically possible to do but it's going to be so much more difficult that it's pragmatically not doable for anyone except giant conglomerates or nation state actors on such chips.
I'd also imagine that some of the higher level things like efficiency and larger behavior would be essentially impossible to do from that side too. I suspect you'd be more likely to be able to get that through the more usual corporate espionage pathways than by trying to reverse it from hardware. Things like figuring out how the clock domains and such act asynchronously and other things like that to power down certain regions of the circuits is and other behavior isn't really going to be obvious from the silicon and metal layers.
reactor3d 2 days ago [-]
[dead]
RetroTechie 3 hours ago [-]
"Signetics announced its first product in 1962, a NAND gate that cost $125 (over $1000 in current dollars)"
By 'coincidence', a quad NAND gate is also the 1st entry in the famous 7400 series of logic ICs (where I'm using 7400 to refer to any of LS, HC(T) etc with compatible pinouts).
One reason will be that a NAND function takes relatively few transistors to implement. Another being that combine-and-invert functions can double as inverters. And those in turn find use in oscillator circuits. So this made for a versatile part in a designer's inventory.
"One of the most popular is the plastic DIP (Dual In-line Package)"
WAS, Ken, was... lol. Unless you're talking surface-mount. Edit - those have their own name: Small Outline Integrated Circuit (SOIC).
Fwiw: I always liked their use to route a signal from one side of a board to the other side, without drilling an extra hole. Most pcb traces rougly North-South on 1 side, roughly East-West on the other side. Maaany early computers were layed out that way on 2-layer boards (or even 1-layer with lots of wire bridges).
The text says that the 616A uses the two diodes that are unused in the 680A but your hypothesized metal layer for the 616A shows those diodes as being unused. They are shown as being used in the hypothesized metal layer for the 670A though. The 670A and the 680A both need 12 diodes and the 616A only needs 10, if I counted correctly. And yet there are 14 total diodes on the die so none of these three models needs all of them. Maybe it was easier to route the signals this way?
To improve their speed, one must use a totem-pole output, where at the output the pull-up resistor is replaced by a transistor, so that the output can charge quickly a capacitive load, ensuring fast transitions from low to high.
Then only 1 of the 2 output transistors is on, depending on the logic state.
So those 2 transistors must have inputs of opposite polarities. This is done by connecting the pull-up transistor to the collector of the driver transistor and the pull-down transistor to the emitter of the driver transistor.
In the gate with totem-pole output, there must be a level-shifting diode connected to the base of the driver transistor, to ensure that the threshold between "0" and "1" is the same at input and at output, i.e. the threshold is equal with 2 silicon diode voltage drops (the 2 diodes are the emitter junction of the driver transistor in series with the emitter junction of the pull-down output transistor), i.e. approximately 1.4 volt (which is the midpoint between the levels that are defined as the limits for "0" and "1", i.e. 0.8 volt and 2.0 volt, leaving a margin for noise that will not cause a wrong logic value).
When an input to the totem-pole DTL goes from high to low, the level-shifting diode becomes reverse biased, so current cannot pass through it, so the driver transistor remains with an open base. Bipolar transistors that are blocked by leaving their base open, become off only very slowly, because there is no path to evacuate the charge carriers from their base region, and until all mobile charge carriers from the base decay by recombination, the transistor remains on, which may take many microseconds.
In TTL, the difference from totem-pole DTL is that the input diodes and the level-shifting diode are no longer separated by an isolation diffusion and they are close enough so that the bipolar transistor effect appears between them.
Thus the input diodes become multiple emitter junctions of a bipolar transistor, while the level-shifting diode becomes the collector junction of that transistor.
The bipolar transistor effect consists in the fact that if there exists an emitter current, it passes through the collector junction, despite the fact that it is reverse biased, which in an isolated diode would prevent the passing of any current.
Thus the transistor effect ensures that when the input goes from high to low, there is a current through the level-shifting diode, which removes the mobile charge carriers from the base of the driver transistor, ensuring that it becomes off immediately, so the TTL gate switches faster than the DTL gate when the input goes from high to low (and the output goes from low to high, because the simplest TTL and DTL gates are inverting gates).
After TTL gates with a power supply of 5 volt replaced the DTL gates in computers, there was a DTL variant that survived until the mid seventies. That DTL variant used a higher supply voltage, typically of 15 volt, to ensure a high noise immunity in industrial applications, where the lower speed also did not matter much. That variant of DTL was eventually replaced by the CMOS 4000 series of logic circuits, initially introduced by RCA, which used the same power supply, but which had a much lower power consumption.
A typical SLT module is shown here: https://ibm-slt-reference.fandom.com/wiki/361412
But seriously, is it possible to analyze the modern chips like Apple M1 using the same methods? To find out, for instance, why there are so much more efficient than Intel CPUs?
I'd also imagine that some of the higher level things like efficiency and larger behavior would be essentially impossible to do from that side too. I suspect you'd be more likely to be able to get that through the more usual corporate espionage pathways than by trying to reverse it from hardware. Things like figuring out how the clock domains and such act asynchronously and other things like that to power down certain regions of the circuits is and other behavior isn't really going to be obvious from the silicon and metal layers.
By 'coincidence', a quad NAND gate is also the 1st entry in the famous 7400 series of logic ICs (where I'm using 7400 to refer to any of LS, HC(T) etc with compatible pinouts).
One reason will be that a NAND function takes relatively few transistors to implement. Another being that combine-and-invert functions can double as inverters. And those in turn find use in oscillator circuits. So this made for a versatile part in a designer's inventory.
"One of the most popular is the plastic DIP (Dual In-line Package)"
WAS, Ken, was... lol. Unless you're talking surface-mount. Edit - those have their own name: Small Outline Integrated Circuit (SOIC).
Fwiw: I always liked their use to route a signal from one side of a board to the other side, without drilling an extra hole. Most pcb traces rougly North-South on 1 side, roughly East-West on the other side. Maaany early computers were layed out that way on 2-layer boards (or even 1-layer with lots of wire bridges).